Parts & Accessories
Whisky Parts Co. Tubeless Rim Tape.
Our thru-axle kit comes with everything you need to mount most 12x142 thru-axle bikes on your KICKR SNAP indoor trainer. This accessory will work with all editions of the Wahoo KICKR SNAP. It includes the following: - Threaded axle spacer M12 x 1.75 Coarse - M12 x 1.5 Medium - M12 x 1.0 Fine - End Cap
Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).
This lightweight, high-pressure rim tape offers great protection against spoke hole flats and is easy to install. This Italian-made tape is light and thin, so it will not inhibit tire fitting. Nylon elastic material is used to ensure a snug fit without movement.
Stan's Cross Country 29er Rim Strip converts standard tubed wheels to tubeless so you can reap the benefits. Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's rim strips create a tight seal with the tire bead, reducing the instances of "burping". Plus, you won't miss dealing with flat tires and you'll save money on tubes!
Lay down Stan's Universal Kit Rim Tape before the tubeless conversion of your non-Stan's rims. It makes your rims air tight and ready for tubeless use by covering the spoke holes.
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
Lightweight and easy to install, there are Ritchey rim strips for all wheel sizes and types. - Easily snaps over your rims - Stretchy, tightly woven material provides a close fit and protects from abrasion - Sold as a pair - Not for tubeless set up
This Shimano HG freehub body is designed for our top level Silverton SL wheelset, which feature DT Swiss hub internals.
Rotorset to convert DT Swiss hubs to accept a Shimano XTR rotor.
-Replacement left side cone and locknut for Shimano 105 FH-5800 rear hub
Add an Alfine hub, cog, spokes, and a rim to this Shimano Internally Geared Hub Small Parts Kit, and you're ready to rock. - Alfine hubs are packaged without small parts and require this kit plus a cog - Nexus hubs are packaged with small parts and cogs and do not require an additional small parts kit - For 11-Speed Hub - Includes CJ-S700 Cassette Joint for Vertical Dropouts *Cassette joint does not fit Di2 Alfine hubs
Shimano Nexus and Alfine Internally Geared Hub Cassette Joints - Shimano model # CJ-S7000 - Does not include cable fixing bolt unit - OEM cassette joint unit for Alfine SG-S7000-8
If the bearings are getting rough on your Shimano Internally Geared hub, it could simply be a matter of replacing a pitted cone and repacking the bearing with grease. - Fits left side of Alfine SG-S700 hubs
Keeping that well-functioning Shimano Alfine internally geared hub in top working condition means keeping the internals clean. Replace the left hub seal ring when necessary for continued performance and to preserve the longevity that you expect from Alfine.
Keeping contamination out of your internally geared hub is critical to its function and longevity. Sometimes, the oil port bolt comes loose and it's easy to lose, even if you've just taken it out to oil your hub. Keep a spare or two so your hub stays clean inside and it'll last you many, many miles.
New cones make hubs spin like silk. Take advantage of your Shimano Alfine hub's highly serviceable design, and replace the bearing cones if they are worn or damaged. This one is specifically for the right side.
Don't let a bent or worn dust cap sully an otherwise well-functioning Shimano Alfine internally geared hub. Get a spare and replace as necessary for continued performance and to preserve the longevity that you expect from Alfine.
Do you need to replace the right lock washer seal on your Alfine SG-S700 internally geared hub? If you're not sure, it might not be a bad idea, as contamination from damaged or worn seals is the kryptonite of virtually maintenance-free internally geared hubs.
Page 1 of 1